For outdoor projects of every size, Craftsman chainsaws are a popular choice due to their value and reliability. If your chainsaw fails to start, you may have to put important projects on hold until you can get it fixed. Follow these simple troubleshooting procedures and replace worn Craftsman chainsaw parts to get your chainsaw back to work as soon as possible. Check the Spark Plug A worn or broken spark plug can keep the chainsaw from igniting, and it is one of the most common reasons for users to buy.
Remove the wire from the spark plug and take it out of the chainsaw to check it for corroded areas, deposits or damaged electrodes. Clean or replace the spark plug, and ensure adequate gaps when placing it back into your Craftsman chainsaw. Test the Compression A chainsaw can't start without compression in the cylinder, so check for adequate compression by removing the spark plug and placing your thumb over the hole.
If air doesn't push out when you pull the starter cord, you may need to replace the piston rings. Use a compression gauge when testing compression for more exact. Replace the Fuel Your chainsaw may not start if the tank is holding old fuel that has gathered moisture, making it difficult to burn. Drain the fuel tank completely if your Craftsman chainsaw has sat unused for several months, and add new fuel using the mixture ratio detailed in your chainsaw's user manual. Sears PartsDirect carries a wide variety of Craftsman chainsaw replacement parts for all your repair needs.
For help and replacement parts specific to your chainsaw maintenance, choose your model from the list above, click the chat button, or call 1-800-252-1698. Script section containing code for 24x7 chat solution. FREE Standard Shipping on orders of $ or more Purchase requirement calculated before taxes and shipping charges and after other discounts have been applied and must be made in a single transaction. Cannot be applied to previous purchases and cannot be redeemed for cash. Valid for standard ground shipping within the continental United States and not valid for shipments to Alaska, Hawaii, Puerto Rico, Guam and the US Virgin Islands.
Nokia pc suite 4 81 download itunes. Offer valid for online purchases only. In an event of a return, coupon savings may be deducted from your refund. Discount will be automatically applied during check-out. Sears Holdings reserves the right to terminate or modify this offer at any time for failure to comply with its terms and/or due to any operational malfunction of the software, hardware or equipment required to process this offer.
© 2013 Sears Brands, LLC. May not be used with any other coupon, associate discount, or during Family & Friends or Member events.
Thank you for your question. I can understand wanting to know what oil you can use. If you are thinking of using the sae 30 oil for lubricating the chain and bar that is okay in a pinch.
I the case of lubricating the chain and bar, any oil am better than no oil. If you are thinking of using it in the engine as a fuel mix please do not do that as it is not an ash-less oil and could do damage to the engine. 32 lives crack download.
I hope this will answer your question and if you have any further questions please reply and I will be happy to help you. Thank you for using Manage My Life.
Craftsman 16 Inch 36cc Chainsaw Parts
Craftsman manufactures a wide variety of small engine products, from leaf blowers and chainsaws up to larger riding lawn tractors. Craftsman chainsaws have a two-cycle engine that combines oil and gasoline to burn as fuel. The carburetor takes the mixture and controls the amount of fuel and air going to the engine, causing the engine to increase or decrease in speed. As the engine begins to wear, the performance of the chainsaw may decline. Adjust the carburetor, to allow the chainsaw to operate at peak performance.
Thank you for your question. I am sorry you are having a problem with the saw. There could one of a few problems. Once you have the starter assembly off try to turn the starter rope pulley in the direction. Be careful if the recoil was just stuck by debris it will recoil quickly. If this happens just pull the rope a few times while holding the recoil up right.
The dirt should fall out. If the rope will not retract and the pulley feels loose, I suspect the spring is broken. If you chose to replace the spring, wear eye and hand protection.
Then remove the screw in the center of the recoil. Now turn the pulley side to side just to make sure there is not ant spring tension. Then lift the pulley off the shaft. This is where you need to be careful, if the spring comes out of the housing it will uncoil rapidly.
If the spring stays in, note the position of the spring and remove it. Then reinstall the new spring in the reverse manner. Once together click here to watch a video on how to wind the spring.
Here is a link to order any parts you need. Sears Parts Direct. If you do not feel confident repairing this problem yourself, then you can have it repaired by a Sears technician. Here is a link that will provide the nearest drop-off locations: Sears Home Services.
Please let me know if you need further assistance. Thank you for using Manage my life.
Brusca epub Invertebrates, pdf Richard C. Brusca pdf, by Richard C. Brusca pdf Invertebrates, Richard C. Brusca invertebrates 3rd edition pdf. Brusca Invertebrates, book pdf Invertebrates, by Richard C. Invertebrates Invertebrates PDF Tags Online PDF Invertebrates, Read PDF Invertebrates, Full PDF Invertebrates, All Ebook Invertebrates, PDF and EPUB Invertebrates, PDF ePub Mobi Invertebrates, Reading PDF Invertebrates, Book PDF Invertebrates, read online Invertebrates, Invertebrates Richard C.
Hi I know these saws inside out. The choke is also the fast idle cam. When you pull the choke on it steps up to fast idle.
If you push the choke in without touching the throttle it stays on fast idle. On fast idle the chain has to turn because the clutch is engaged. As soon as you touch the throttle it kicks down to slow idle. The chain should stop and the engine should idle slowly. From what I read in your post is that as soon as you takle it off high idle it stalls. That is a simple setting of the throttle position screw.
(The top adjusting screw that is all by itself.) The high speed and low speed are close together and are marked H and L. Simply turn the throttle position screw in until it idles properly then adjust the low speed screw (very slight turning) until it runs as fast and smooth as possible. Re-adjust the idle speed and you're good to go.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |